Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

气藏型储气库注气期试井分析探讨

针对气藏型储气库注采井注采过程中储层物性参数影响因素不明确、注采能力不对称的问题。基于相国寺储气库井下连续油管试井测试结果,提出储气库注气期“温降效应”、“变表皮效应”的概念,分析了储气库注采过程中温降效应、变表皮效应以及储层应力敏感对注采的影响。通过气藏型储气库注气期试井分析技术,研究各因素在试井曲线上的响应特征以及对试井解释参数的影响。结果表明:①相对于采气期试井测试,注气期测试得到的储层物性参数具有同样的参考价值;②储气库温降效应对于试井解释结果的影响可忽略不计,而在不同注采运行周期内,变表皮效应以及应力敏感效应影响差异较大;③编制储气库注采运行方案时应充分考虑变表皮效应与应力敏感的影响,在不同注采运行周期内开展试井测试获取准确的储层参数值。研究成果为储气库试井测试与解释提供了重要的研究依据和理论指导。     

Fabrication and characterizations of Cr3+-doped ZnGa2O4 transparent ceramics with persistent luminescence

0.5 at.% Cr:ZnGa₂O₄ precursor was synthesized by the co-precipitation method with nitrates as raw materials, using ammonium carbonate as the precipitant. Low-agglomerated Cr:ZnGa₂O₄ powders with an average particle size of 43 nm were obtained by calcining the precursor at 900℃ for 4 h. Using the powders as starting materials, 0.5 at.% Cr:ZnGa₂O₄ ceramics with an average grain size of about 515 nm were prepared by presintering at 1150℃ for 5 h in air and HIP post-treatment at 1100℃ for 3 h under 200 MPa Ar. The in-line transmittance of 0.5 at.% Cr:ZnGa₂O₄ ceramics with a thickness of 1.3 mm reaches 59.5% at the wavelength of 700 nm. The Cr:ZnGa₂O₄ ceramics can be effectively excited by visible light and produce persistent luminescence at 700 nm. For Cr:ZnGa₂O₄ transparent ceramics, the brightness of afterglow was larger than 0.32 mcd/m² after 30 min, which is far superior to that of Cr:ZnGa₂O₄ persistent luminescence powders.     

30Cr13不锈钢冶炼过程夹杂物控制技术

  针对30Cr13生产过程中存在的轧材非金属夹杂物合格率偏低仅85%左右的问题，通过对30Cr13不锈钢精炼过程钢中非金属夹杂物存在形态进行分析，并结合现有精炼工艺制度，在实验室研究的基础上制定了不锈钢精炼过程非金属夹杂物控制方案。工业应用后，精炼结束钢中大于5 μm的非金属夹杂物总数、形状以及尺寸等参数均得到了有效改善，钢水洁净度大大提高。     

某矿快速掘进最优炮孔间距的选择

山西某矿5308底抽巷在掘进过程中速度慢、效率低，直接影响工作面的瓦斯抽采，为了改善上述情形，对炮孔间距进行研究。通过使用ANSYS软件对不同炮孔间距下快速掘进效果的模拟分析，并经现场验证，得出了适应该矿的最佳炮孔间距。结果表明：炮孔间距为500 mm时，爆破产生裂隙发育范围和岩石损伤区域都最大，快速掘进的效果最好。     

低温水等离子体活化和表面接枝DMAE聚氯乙烯中空纤维膜研究

采用低温水等离子体技术，在三通道聚氯乙烯(PVC)膜表面接枝了甲基丙烯氧基苄基二甲基氯化铵(DMAE)单体，增强了膜亲水和抗菌性能。通过红外分析，表明DMAE成功接枝到了PVC膜上，水通量提高两倍，PVC-ir-H₂O膜(通过水等离子体处理的膜)对牛血清蛋白(BSA)的吸附能力下降67%，对BSA溶液的通量从7.7提高至40 kg?m^-2?h^-1，并且对BSA的截留能力不变。通过静态及动态抗菌实验，接枝后的PVC膜（PVC-g-PMAE膜）抗菌率达到100%，膜组件运行中的抗菌率也达到82%以上。在保证细菌截留率100%的同时，其渗透通量提高三倍。该膜表面修饰工程技术能实现膜表面的均一化改性，且绿色环保、操作简便、成本低，改性膜在饮用水处理领域，尤其是家用净水器中展现了很好的应用前景。